H- CMD7071
DVD/MP3/CD-RECEIVER
DVD/MP3/CD-ɊȿɋɂȼȿɊ
Instruction manual
Ɋɭɤɨɜɨɞɫɬɜɨꢀɩɨꢀɷɤɫɩɥɭɚɬɚɰɢɢ
Important safeguards
Using the device at temperature below -10ºɋ may cause the breakage of the device. BEFORE USING PLEASE
HEAT UP THE PASSENGER COMPARTMENT TO THE RECOMMENDED TEMPERATURE!
Read carefully through this manual to familiarize yourself with this high-quality sound system.
Disconnect the vehicle's negative battery terminal while mounting and connecting the unit.
When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher
amperage rating may cause serious damage to the unit.
DO NOT attempt to disassemble the unit. Laser beams from the optical pickup are dangerous to the eyes.
Make sure that pins or other foreign objects do not get inside the unit; they may cause malfunctions, or create
safety hazards such as electrical shock or laser beam exposure.
If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes
normal before operating the unit.
DO NOT open covers and do not repair yourself. Consult the dealer or an experienced technician for help.
Make sure you disconnect the power supply and aerial if you will not be using the system for a long period or
during a thunderstorm.
Make sure you disconnect the power supply if the system appears to be working incorrectly, is making an
unusual sound, has a strange smell, has smoke emitting from it or liquids have got inside it. Have a qualified
technician check the system.
The unit is designed for negative terminal of the battery, which is connected to the vehicle metal. Please confirm
it before installation.
Do not allow the speaker wires to be shorted together when the unit is switched on. Otherwise it may overload or
burn out the power amplifier.
Do not install the detachable panel before connecting the wire.
3
Installation/Connections
First complete the electrical connections, and then check them for correctness.
Installation opening
This unit can be installed in any dashboard having an opening as shown below. The dashboard should be 4.75 ± 5.56
mm thick in order to be able to support the unit.
1. Insert mounting collar into the dashboard, and bend the mounting tabs out with a screwdriver.
Make sure that lock lever
is flush with the mounting collar (not projecting outward).
2. Secure the rear of the unit.
After fixing mounting bolt and power connector, fix the rear of the unit to the car body by rubber cushion.
3. Insert trim plate.
When you prepare to insert trim plate, please check it¶s direction. Once it was up side down, it cannot be fixed.
IMPORTANT: Remove
these two screws before
installation. Otherwise,
the DVD Player will not
work
4
Electrical connections
5
Do not interchange the connection of the wiring!!!
For some car models you may need to modify wiring of the supplied power cord as illustrated (modified wiring), or
else the memory of the unit may be lost after you power off. Contact your authorized car dealer before installing this
unit.
Using the ISO Connector
1. If your car is equipped with the ISO connector, then connect the ISO
connectors as illustrated.
2. For connections without the ISO connectors, check the wiring in the vehicle
carefully before connecting, incorrect connection may cause serious damage to
this unit.
Cut the connector, connect the colored leads of the power cord to the car battery
as shown in the colour code table below for speaker and power cable
connections.
Location
FUNCTION
Connector A
Connector B
1
2
3
4
5
6
7
8
Rear Right(+)---Purple
Rear Right(-)---Purple/Black Stripe
Front Right(+)---Gray
Front Right(-)---Gray/Black Stripe
Front Left(+)---White
Front Left((-)---White/Black Stripe
Rear Left(+)---Green
Rear Left(-)---Green/Black Stripe
Battery 12V (+)/yellow
Auto Antenna/blue
ACC+/red
Ground/black
6
Panel controls
Front panel
1. POWER BUTTON.
Press POWER/MUTE in 1 second to MUTE ON, press it again 1 second to MUTE OFF.
Press more than 2 seconds POWER/MUTE to power off.
2. LCD (LIQUID CRYSTAL DISPLAY).
3. OPEN BUTTON.
Press it to flip down the front panel and you can insert the disc into the compartment or press the EJ button to
eject the disc from the disc compartment.
4. LOUDNESS
5. FM STEREO/MONO
6. LOCAL/DX BUTTON
7. BAND BUTTON.
Press it repeatedly to select your desired radio band during RADIO mode.
8. AMS BUTTON (AUTO-PRESET/PRESET SCAN).
7
9. PRESET STATION [1-6] AND RPT, RDM BUTTONS.
1. Disc playback: Play/ Pause.
2. Disc playback: Intro play (10 seconds).
3. Disc playback: Track repeat play.
4. Disc playback: Track random play.
5. VIDEO MODE BUTTON (PAL/NTSC).
6. AUDIO CHANEL SWITCH BUTTON (L/R/ST).
10. SRC BUTTON. Press it to select RADIO, CD or AUX mode.
11. DISPLAY SWITCH
12. VOLUME-UP/DOWN, MENU-UP/DOWN.
Back of the front panel
Press the
button to open the panel and press
to eject the disc.
Disc eject
Disc slot: insert a disc for playback here
Reset hole
Panel status indicator
8
Note: Pressing the RESET hole will erase the clock setting and stored stations.
Panel status indicator lights up when you slide the panel down; flashes when you remove the panel.
ISO connector
PLEASE USE ONLY ORIGINAL CONNECTOR WHICH GOES WITH SET.
Note:
In spite of having any kinds of speaker system, must use 4 ohms impedance of speaker to reduce the distortion
during high volume level.
9
Remote control
1. ZOOM button
2. TITLE button
3. Power on/off
4. Setup |